Libre Computer Board : faster than a Raspberry Pi 3

Libre Computer Board

Quad-Core 64-bit 4K UHD development board with up to 2GB RAM, support for Android 7.1, Linux 4.9 LTS + Mainline

It should be faster than a Raspberry Pi 3. And unlike some other devices in this category, it’s not named after a fruit… it’s named for a vegetable.

Compare to other boards:
Improvements over Raspberry Pi 3 Model B

    50% Faster CPU and GPU
    Double RAM Available
    Lower Power Consumption
    Better Android 7.1 and Kodi Support
    Much Better Hardware Accelerated Codec Support
    4K UHD with HDR over HDMI 2.0
    MicroSD Card UHS Support
    eMMC Daughter Board Support
    IR Receiver
    ADC + I2S Headers
    Non-Shared Bandwidth for LAN and USB
    
Differences with Raspberry Pi 3 Model B
    
    No DSI Interface
    No CSI Interface
    No onboard 2.4GHz WiFi/Bluetooth
    Software and images made for Raspberry Pi must be modified to work

Improvements over ASUS Tinkerboard

    ARMv8 64-bit CPU
    10% Faster CPU
    Lower Power Consumption
    No Throttling Problems
    Better Codec Support (VP9, 4K60, HDR Support)
    Better Android 7.1 and Kodi Support
    eMMC Daughter Board Support
    ADC + I2S Headers
    IR Receiver
    Lower Cost
    
Differences with the ASUS Tinkerboard
    
    15% Slower Single Thread CPU Performance
    15% Slower GPU
    No OpenGL ES 3.0
    No DSI Interface
    No CSI Interface
    No Gigabit LAN
    No onboard 2.4GHz WiFi/Bluetooth
    Android TV vs Android Tablet UI







    





评论

发表评论

此博客中的热门博文

ZestET2-J Ethernet FPGA Board

图片
ZestET2-J Ethernet FPGA Board The ZestET2-J is an easy to use FPGA board with Xilinx Artix-7 user programmable FPGA and a very high performance TCP/IP Offload Engine (TOE) chip. The board can be used as a programmable interface to external devices, for high speed processing of streaming data, and for data acquisition and control. It provides a simple bridge between a high speed computer network and a programmable digital interface. The TOE sustains a data rate over 100MBytes/s in each direction and includes a user programmable CPU for optional higher level protocols. For evaluation there are two breakout boards available: ZestET2-J-BRK-H simply connects the User FPGA IO pins to four 0.1” pitch headers. It also has the standard Xilinx JTAG header for the ZestET2-J User FPGA. ZestET2-J-BRK-F connects the User FPGA IO pins to an FMC connector and a 0.1” pitch header. It includes all power supplies for the ZestET2-J and the FMC and is powered from 12V. It also has the st...
阅读全文

NPi i.MX6ULL Dev Board

图片
NPi i.MX6ULL Dev Board A low power, i.MX6ULL-based "sandwich-style" SBC, with 512MB DDR3L RAM, 512MB NAND or 8GB eMMC storage, and I/O including 2x USB and 2x LAN ports, plus 2x 40-pin headers with RPi compatible expansion. Raspberry Pi hats can be directly put into this board. NPi i.MX6ULL board specifications: Core Module SoC – NXP MCIMX6Y2CVM08AB single Cortex-A7 core @ up to 800 MHz System Memory – 512MB DDR3L Storage NPi-i.MX6ULL eMMC module – 8GB flash NPi-i.MX6ULL NAND module – 256 MB NAND flash Breakout Board Storage – MicroSD card slot Display I/F – FPC LCD interface with 24-bit RGB and I2C touch control Networking – 2x 10/100M Ethernet ports USB – 1x USB 2.0 host port, 1x USB Type-C device port Expansion – 2x 40-pin headers including one compatible with Raspberry Pi I/O header with I2C, GPIO, ADC, UART, SPI, CSI, PWM, and the other headers exposing SNVS anti-tampering pins, I2S/SAI, Ethernet, UART, and more GPIOs Debugging – UART TTL for serial cons...
阅读全文

Microsemi A2F-EVAL-KIT-2 SmartFusion Evaluation Kit

图片
The SmartFusion Evaluation Kit board includes:     A2F200M3F-FGG484         200,000 System FPGA gates, 256 KB flash memory, 64 KB SRAM, and additional distributed SRAM in the FPGA fabric and external memory controller         Peripherals include Ethernet, DMAs, I2Cs, UARTs, timers, ADCs, DACs and additional analog resources         Refer to the SmartFusion product page for full device information     SPI-flash memory connected to SPI_0 on the device     USB connection for programming and debug from Microsemi's design tools     USB to UART connection to UART_0 for HyperTerminal examples     10/100 Ethernet interface with on-chip MAC and external PHY     RVI header for application programming and debug from either Keil or IAR Systems     Mixed-signal header for daughter c...
阅读全文